Evolution of ferronickel particles during the reduction of low-grade saprolitic laterite nickel ore by coal in the temperature range of 900–1250℃with the addition of CaO–CaF2–H3BO3

The method of producing ferronickel at low temperature(1250–1400℃)has been applied since the 1950s at Nippon Yakin Kogyo,Oheyama Works,Japan.Limestone was used as an additive to adjust the slag composition for lowering the slag melting point.The ferronickel product was recovered by means of a magnetic separator from semi-molten slag and metal after water quenching.To increase the efficiency of magnetic separation,a large particle size of ferronickel is desired.Therefore,in this study,the influences of CaO,CaF₂,and H₃BO₃ additives on the evolution of ferronickel particle at≤1250℃were investigated.The experiments were conducted at 900–1250℃with the addition of CaO,CaF₂,and H₃BO₃.The reduction processes were carried out in a horizontal tube furnace for 2 h under argon atmosphere.At 1250℃,with the CaO addition of 10 wt%of the ore weight,ferronickel particles with size of 20μm were obtained.The ferronickel particle size increased to 165μm by adding 10 wt%CaO and 10 wt%CaF₂.The addition of boric acid further increased the ferronickel particle size to 376μm,as shown by the experiments with the addition of 10 wt%CaO,10 wt%CaF₂,and 10 wt%H₃BO₃.     

一种立体织机平行打纬机构的设计与优化

针对多层织物织造过程中,各层纬纱打纬力需保持一致以及需要减少钢筘与纱线之间摩擦的要求,提出八连杆平行打纬机构,并根据工艺要求对打纬机构进行优化。以打纬机构的主轴转动140°时,筘座在后心位置处的近似静止位移Δs最小为优化目标,通过Matlab软件分析确定设计变量,优化钢筘在后死心位置的近似停留时间。运动学仿真结果表明,优化后的打纬机构不仅保证了钢筘的打纬动程和其在后死心处的静止时间,而且增大了钢筘的惯性打纬力,有利于厚重织物的打纬。     

表面纤维直径与羊毛机织精纺面料的刺痒感

通过前臂试验对26种轻薄型羊毛机织精纺面料和7种其他纤维的轻薄型机织面料的刺痒感进行了比较研究,并用显微镜对部分轻薄型羊毛机织面料的表面纤维分布进行了研究。结果表明多数毛织物在温度为(24±1)℃、相对湿度为(65±5)％的条件下存在刺痒感,并且毛织物的刺痒感与其表面纤维的平面直径及直径大于26μm的表面纤维根数密切相关。     

人工气候条件下的人体着装试验的研究

本文通过物理试验方法对棉、毛、丝、棉麻及毛涤五种面料进行性能测试,得出其风格数值、透湿阻抗.为了反映面料对人的生理、心理的影响,有必要在人工气候条件下进行人体模拟着装试验,得出面料的人体舒适感觉值。借助多元线性回归方法,通过物理测试与人体试验的对照分析,发现它们之间具有良好的一致性。     

合理预留安全矿柱的探讨

矿床地下开采时,在没有其他安全措施的情况下,不得不采用预留安全矿柱的方法,以保护地面建筑物、构筑物和主要井巷免受因地下采矿而引起的破坏。但这会导致矿量的损失,故需要寻找合理预留安全矿柱的方法。作者用解析的方法对预留安全矿柱进行研究,突破了常用的传统方法。     

纯棉针织物活性染料预碱法染色工艺研究

采用传统染色工艺和预减法染色工艺，对纯棉针织物进行染色实验。通过对各自固色率的分析比较，并从活性染料的染色原理进行分析，指出预减法染色可以提高活性染料的固色率。     

Three-Dimensional Measurement and Reconstruction of Fabric Drape Shape

This paper introduces a new method of measuring the three-dimensional drape shape of fabrics with structural light. First, we apply parallel annular structural light to form light and shade alternating contour stripes on the surface of fabrics. We then collect the images of contour stripes using Charge Coupled Device （CCD）. Subsequently, we process the images to identify the contour stripes and edges of fabrics, and obtain the fabric contour lines of curved surfaces. Finally, we apply three-dimensional curved surface modeling method based on a network of polar coordinates, and reconstruct the three-dimensional drape shape of fabrics. Experiments show that our method is effective in testing and reconstructing three-dimensional drape shape of fabrics.     

经编针织运动服装的织物性能研究

从人体穿着舒适性能考虑,织物的热湿舒适性越来越成为人们重视的服用性能.本文针对功能性的针织运动服的原料选用和织物组织结构,分析其导湿性.     

唐钢二炼铁厂使用巴西MBR块矿的生产应用

分析了巴西MBR块矿的矿相结构、矿物组成及冶金性能.MBR块矿的各项冶金性能较好,与烧结矿组成的综合炉料在高炉内的同化过程开始温度和结束温度均较高,但同化速度相对减慢.唐钢二炼铁厂的炼铁生产实践结果表明,适当配用MBR块矿,高炉入炉品位上升,矿耗降低,综合焦比下降,铁成本降低,高炉顺行状态良好.MBR块矿在改善高炉综合技术经济指标的过程中起着重要作用.